Wheel Spacers

Eibach Pro-Spacer wheel spacers for the front axle of the Ford Mustang 2005–2014 – 40 mm per axle or 20 mm per wheel. Eibach Pro-Spacer wheel spacers increase the track width of the Mustang and allow the position of the wheels within the wheel arches to be adjusted. This set is designed for the front axle and increases the total track width by 40 mm – 20 mm per wheel. The silver anodised aluminium spacers use the Eibach System 4. The spacers are bolted directly to the vehicle using the supplied mounting hardware, with integrated wheel studs then used to mount the wheel. 40 mm wider track at the front axle 40 mm track increase per axle 20 mm spacer per wheel for the front axle Eibach Pro-Spacer System 4 bolt-on system with wheel studs aluminium construction silver anodised finish mounting hardware included Teilegutachten included Suitable for Ford Mustang 2005–2014 Coupe and Convertible front axle Which spacer width fits my Mustang? The spacer width that can actually be used on your Mustang depends on the individual vehicle and wheel/tyre combination. Important factors include wheel width, offset, tyre size, vehicle ride height, wheel clearance and sufficient tyre coverage. Please check wheel clearance and sufficient tyre coverage on your vehicle before ordering. The requirements of the supplied Teilegutachten apply to the approved wheel/tyre combinations and any additional measures that may be required. Installation and approval The System 4 spacers are attached to the vehicle using the specified mounting hardware. The wheel is then mounted to the studs integrated into the spacer. For use in Germany, an inspection according to §19(3) StVZO is required after installation in accordance with the supplied Teilegutachten. All requirements applicable to the respective wheel and tyre combination must be observed. The mounting hardware must be checked and retightened after installation in accordance with Eibach's instructions. Scope of delivery 2x Eibach Pro-Spacer 20 mm wheel spacer mounting hardware Teilegutachten Eibach part number: S90-4-20-016 Image for illustration purposes only – the product image shows a standard Eibach Pro-Spacer image. The actual product supplied may differ in appearance.

Eibach Pro-Spacer wheel spacers for the rear axle of the Ford Mustang 2005–2014 – 40 mm per axle or 20 mm per wheel. Eibach Pro-Spacer wheel spacers increase the track width of the Mustang and allow the position of the wheels within the wheel arches to be adjusted. This set is designed for the rear axle and increases the total track width by 40 mm – 20 mm per wheel. The silver anodised aluminium spacers use the Eibach System 4. The spacers are bolted directly to the vehicle using the supplied mounting hardware, with integrated wheel studs then used to mount the wheel. 40 mm wider track at the rear axle 40 mm track increase per axle 20 mm spacer per wheel for the rear axle Eibach Pro-Spacer System 4 bolt-on system with wheel studs aluminium construction silver anodised finish mounting hardware included Teilegutachten included Suitable for Ford Mustang 2005–2014 Coupe and Convertible rear axle Which spacer width fits my Mustang? The spacer width that can actually be used on your Mustang depends on the individual vehicle and wheel/tyre combination. Important factors include wheel width, offset, tyre size, vehicle ride height, wheel clearance and sufficient tyre coverage. Please check wheel clearance and sufficient tyre coverage on your vehicle before ordering. The requirements of the supplied Teilegutachten apply to the approved wheel/tyre combinations and any additional measures that may be required. Installation and approval The System 4 spacers are attached to the vehicle using the specified mounting hardware. The wheel is then mounted to the studs integrated into the spacer. For use in Germany, an inspection according to §19(3) StVZO is required after installation in accordance with the supplied Teilegutachten. All requirements applicable to the respective wheel and tyre combination must be observed. The mounting hardware must be checked and retightened after installation in accordance with Eibach's instructions. Scope of delivery 2x Eibach Pro-Spacer 20 mm wheel spacer mounting hardware Teilegutachten Eibach part number: S90-4-20-017 Image for illustration purposes only – the product image shows a standard Eibach Pro-Spacer image. The actual product supplied may differ in appearance.

Eibach Pro-Spacer wheel spacers for the front axle of the Ford Mustang 2005–2014 – 50 mm per axle or 25 mm per wheel. Eibach Pro-Spacer wheel spacers increase the track width of the Mustang and allow the position of the wheels within the wheel arches to be adjusted. This set is designed for the front axle and increases the total track width by 50 mm – 25 mm per wheel. The silver anodised aluminium spacers use the Eibach System 4. The spacers are bolted directly to the vehicle using the supplied mounting hardware, with integrated wheel studs then used to mount the wheel. 50 mm wider track at the front axle 50 mm track increase per axle 25 mm spacer per wheel for the front axle Eibach Pro-Spacer System 4 bolt-on system with wheel studs aluminium construction silver anodised finish mounting hardware included Teilegutachten included Suitable for Ford Mustang 2005–2014 Coupe and Convertible front axle Which spacer width fits my Mustang? The spacer width that can actually be used on your Mustang depends on the individual vehicle and wheel/tyre combination. Important factors include wheel width, offset, tyre size, vehicle ride height, wheel clearance and sufficient tyre coverage. Please check wheel clearance and sufficient tyre coverage on your vehicle before ordering. The requirements of the supplied Teilegutachten apply to the approved wheel/tyre combinations and any additional measures that may be required. Installation and approval The System 4 spacers are attached to the vehicle using the specified mounting hardware. The wheel is then mounted to the studs integrated into the spacer. For use in Germany, an inspection according to §19(3) StVZO is required after installation in accordance with the supplied Teilegutachten. All requirements applicable to the respective wheel and tyre combination must be observed. The mounting hardware must be checked and retightened after installation in accordance with Eibach's instructions. Scope of delivery 2x Eibach Pro-Spacer 25 mm wheel spacer mounting hardware Teilegutachten Eibach part number: S90-4-25-032 Image for illustration purposes only – the product image shows a standard Eibach Pro-Spacer image. The actual product supplied may differ in appearance.

Eibach Pro-Spacer wheel spacers for the rear axle of the Ford Mustang 2005–2014 – 50 mm per axle or 25 mm per wheel. Eibach Pro-Spacer wheel spacers increase the track width of the Mustang and allow the position of the wheels within the wheel arches to be adjusted. This set is designed for the rear axle and increases the total track width by 50 mm – 25 mm per wheel. The silver anodised aluminium spacers use the Eibach System 4. The spacers are bolted directly to the vehicle using the supplied mounting hardware, with integrated wheel studs then used to mount the wheel. 50 mm wider track at the rear axle 50 mm track increase per axle 25 mm spacer per wheel for the rear axle Eibach Pro-Spacer System 4 bolt-on system with wheel studs aluminium construction silver anodised finish mounting hardware included Teilegutachten included Suitable for Ford Mustang 2005–2014 Coupe and Convertible rear axle Which spacer width fits my Mustang? The spacer width that can actually be used on your Mustang depends on the individual vehicle and wheel/tyre combination. Important factors include wheel width, offset, tyre size, vehicle ride height, wheel clearance and sufficient tyre coverage. Please check wheel clearance and sufficient tyre coverage on your vehicle before ordering. The requirements of the supplied Teilegutachten apply to the approved wheel/tyre combinations and any additional measures that may be required. Installation and approval The System 4 spacers are attached to the vehicle using the specified mounting hardware. The wheel is then mounted to the studs integrated into the spacer. For use in Germany, an inspection according to §19(3) StVZO is required after installation in accordance with the supplied Teilegutachten. All requirements applicable to the respective wheel and tyre combination must be observed. The mounting hardware must be checked and retightened after installation in accordance with Eibach's instructions. Scope of delivery 2x Eibach Pro-Spacer 25 mm wheel spacer mounting hardware Teilegutachten Eibach part number: S90-4-25-033 Image for illustration purposes only – the product image shows a standard Eibach Pro-Spacer image. The actual product supplied may differ in appearance.

Eibach Pro-Spacer wheel spacers for the front axle of the Ford Mustang 2005–2014 – 60 mm per axle or 30 mm per wheel. Eibach Pro-Spacer wheel spacers increase the track width of the Mustang and allow the position of the wheels within the wheel arches to be adjusted. This set is designed for the front axle and increases the total track width by 60 mm – 30 mm per wheel. The silver anodised aluminium spacers use the Eibach System 4. The spacers are bolted directly to the vehicle using the supplied mounting hardware, with integrated wheel studs then used to mount the wheel. 60 mm wider track at the front axle 60 mm track increase per axle 30 mm spacer per wheel for the front axle Eibach Pro-Spacer System 4 bolt-on system with wheel studs aluminium construction silver anodised finish mounting hardware included Teilegutachten included Suitable for Ford Mustang 2005–2014 Coupe and Convertible front axle Which spacer width fits my Mustang? The spacer width that can actually be used on your Mustang depends on the individual vehicle and wheel/tyre combination. Important factors include wheel width, offset, tyre size, vehicle ride height, wheel clearance and sufficient tyre coverage. Please check wheel clearance and sufficient tyre coverage on your vehicle before ordering. The requirements of the supplied Teilegutachten apply to the approved wheel/tyre combinations and any additional measures that may be required. Installation and approval The System 4 spacers are attached to the vehicle using the specified mounting hardware. The wheel is then mounted to the studs integrated into the spacer. For use in Germany, an inspection according to §19(3) StVZO is required after installation in accordance with the supplied Teilegutachten. All requirements applicable to the respective wheel and tyre combination must be observed. The mounting hardware must be checked and retightened after installation in accordance with Eibach's instructions. Scope of delivery 2x Eibach Pro-Spacer 30 mm wheel spacer mounting hardware Teilegutachten Eibach part number: S90-4-30-019 Image for illustration purposes only – the product image shows a standard Eibach Pro-Spacer image. The actual product supplied may differ in appearance.

Eibach Pro-Spacer wheel spacers for the rear axle of the Ford Mustang 2005–2014 – 60 mm per axle or 30 mm per wheel. Eibach Pro-Spacer wheel spacers increase the track width of the Mustang and allow the position of the wheels within the wheel arches to be adjusted. This set is designed for the rear axle and increases the total track width by 60 mm – 30 mm per wheel. The silver anodised aluminium spacers use the Eibach System 4. The spacers are bolted directly to the vehicle using the supplied mounting hardware, with integrated wheel studs then used to mount the wheel. 60 mm wider track at the rear axle 60 mm track increase per axle 30 mm spacer per wheel for the rear axle Eibach Pro-Spacer System 4 bolt-on system with wheel studs aluminium construction silver anodised finish mounting hardware included Teilegutachten included Suitable for Ford Mustang 2005–2014 Coupe and Convertible rear axle Which spacer width fits my Mustang? The spacer width that can actually be used on your Mustang depends on the individual vehicle and wheel/tyre combination. Important factors include wheel width, offset, tyre size, vehicle ride height, wheel clearance and sufficient tyre coverage. Please check wheel clearance and sufficient tyre coverage on your vehicle before ordering. The requirements of the supplied Teilegutachten apply to the approved wheel/tyre combinations and any additional measures that may be required. Installation and approval The System 4 spacers are attached to the vehicle using the specified mounting hardware. The wheel is then mounted to the studs integrated into the spacer. For use in Germany, an inspection according to §19(3) StVZO is required after installation in accordance with the supplied Teilegutachten. All requirements applicable to the respective wheel and tyre combination must be observed. The mounting hardware must be checked and retightened after installation in accordance with Eibach's instructions. Scope of delivery 2x Eibach Pro-Spacer 30 mm wheel spacer mounting hardware Teilegutachten Eibach part number: S90-4-30-020 Image for illustration purposes only – the product image shows a standard Eibach Pro-Spacer image. The actual product supplied may differ in appearance.