Accessories

The BMR DSL017 Driveshaft Safety Loop is a heavy-duty safety restraint for the Ford Mustang driveshaft. Installed around the front section of the driveshaft, it is designed to help contain the driveshaft in this area underneath the vehicle in the event of a failure. The Safety Loop does not alter the operation of the driveshaft and is not a suspension or performance modification. Its purpose is to provide an additional level of protection in the event that a driveshaft or its connection fails under high load. What does a Driveshaft Safety Loop do? At high vehicle speeds, the driveshaft rotates at correspondingly high speed. In the unlikely event that it becomes disconnected or fails while driving, an uncontrolled driveshaft underneath the vehicle can potentially cause significant secondary damage. The BMR Safety Loop surrounds the front section of the driveshaft. In the event of a failure, it is designed to help contain the driveshaft in this area underneath the vehicle and thereby reduce the risk of additional damage. Additional protection at high speeds For a Mustang that is regularly driven at high speeds, a Driveshaft Safety Loop can provide a useful additional mechanical safeguard. On 2015 and later Mustang models, the factory driveshafts are already designed for the higher vehicle speeds these models can achieve. The Safety Loop is therefore not a prerequisite for higher-speed driving on these vehicles, but it can be installed as an additional mechanical safety measure. Particularly relevant for 2011–2014 Mustangs On 2011–2014 Mustang models, this becomes particularly relevant when the factory speed limiter is removed. Especially on V6 models, it should be taken into account that the factory driveshaft was not designed for unrestricted increases in vehicle speed. A Safety Loop does not make an unsuitable driveshaft safe for higher speeds and does not replace any necessary driveshaft upgrade. It does, however, provide an additional safeguard for the worst-case scenario if the driveshaft or one of its connections should fail. Heavy-duty bolt-on construction The DSL017 is manufactured from 0.25-inch laser-cut steel plate and attaches to the factory transmission crossmember. Its fully bolt-on design requires no welding. High-strength Grade 8 mounting hardware is included. BMR specifies an installation time of approximately one hour. Vehicle applications 2011–2014 Ford Mustang 2015–2023 Ford Mustang 2024 and later Ford Mustang Suitable for various engines and model variants Compatible with MGW shifters Product features BMR part number DSL017 Additional driveshaft safety restraint Can help reduce the risk of secondary damage in the event of a driveshaft failure 0.25-inch laser-cut steel construction Black Hammertone finish Attaches to the factory transmission crossmember 100% bolt-on installation Grade 8 mounting hardware included No welding required Made in the USA

The Schropp Exhaust Tip Set gives the factory Ford quad-exhaust system a considerably more distinctive and premium appearance. The four round exhaust tips feature a 100 mm diameter, angled outlets and wide rolled edges and are installed over the existing factory exhaust tips. The major advantage: the original Ford exhaust tips do not need to be cut off. The Schropp tips simply slide over the existing tips and are then securely fixed in position with weld points. The set is suitable for both the Mustang 6 Facelift and Mustang 7 equipped with the factory Ford quad-exhaust system. Discontinued product – only a few sets remaining This exhaust tip set is a discontinued product and will no longer be available once our remaining stock has been sold. Our previous supplier is no longer in business and we are therefore unable to source further sets. These are regular new products from our remaining inventory – not used parts or B-stock. More distinctive looks without replacing the factory exhaust With their 100 mm diameter, the Schropp exhaust tips create a considerably more prominent appearance than the standard outlets. The angled design and wide edges give the rear of the Mustang a clean and sporty appearance. The tips are deliberately designed without logos or branding. This creates a clean appearance and allows them to look like a natural extension of the factory exhaust system. The original exhaust tips remain in place Installation does not require the factory exhaust tips to be cut off. The new tips slide over the existing outlets, are aligned in position and subsequently secured with weld points. The actual factory Ford exhaust system therefore remains intact and no extensive modification of the exhaust system is required. Supplied with approval documentation The Schropp Exhaust Tip Set is supplied with approval documentation, providing the relevant documentation for road-legal installation. Product features Complete set of 4 exhaust tips Diameter: 4x 100 mm Round design Angled outlets Wide edges Clean appearance without logos or branding Installed over the factory exhaust tips No cutting of the original exhaust tips required Secured in position with weld points Supplied with approval documentation Vehicle applications Mustang 6 Facelift 2018–2023 with factory Ford quad-exhaust system Mustang 7 from 2024 with factory Ford quad-exhaust system Discontinued product: Only a few sets remain in stock. Once sold out, this product will no longer be available.